Search

MT3608 2A Max DC-DC Step Up Power Module Booster Power Module

Products > Other Module > MT3608 2A Max DC-DC Step Up Power Module Booster Power Module
    • 1
    • 2
    • 3
    • 4

MT3608 2A Max DC-DC Step Up Power Module Booster Power Module

shared：


Features:

MT3608 2A Max DC-DC Step Up Power Module Booster Power Module

 

Features:
1. Maximum output current: 2A
2. Input voltage: 2 v - 24 v
3. Maximum output voltage:> 5V-28 v
4. Efficiency:> 93%
Smart MT3608 2A Max DC-DC Step Up Power Module Booster Power Module

Note:

1. Input voltage should not exceed the maximum input voltage
2. Peak current output current does not exceed 2A
3.  When the module output voltage can not be adjusted, always equal to the input voltage when
the first 20 laps counterclockwise rotary potentiometer or more, then you can use the module
properly regulate the voltage. Surge mode: potentiometer face chest, counterclockwise turn boost!
Smart MT3608 2A Max DC-DC Step Up Power Module Booster Power Module


Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit

4S 30A High Current Li-ion Lithium Battery 18650 Charger Protection Board 14.4V 14.8V 16.8V BMS

1. Module name: 4 series lithium battery protection board 2. Modular nature: polymer lithium battery protection board 3. Overcharge detection voltage: 4.25 ± 0.025V 4. Overcharge release voltage: 4.15 ± 0.05V 5. Overdischarge detection voltage: 2.50 ± 0.08V 6. Over-discharge termination voltage: 3 ± 0.1V 7. Overcurrent: 20-30A

L298N motor driver board module intelligent vehicle robot accessory H-bridge drive stepper motor driver

TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection

GSM module, SIM808 Module with GPS antenna GSM GPRS GPS development board

This module is 5-12V power supply, when the power supply is less than 9V, 2A DC is required. The other power supply port is 3.5-4.2V, suitable for lithium battery power supply. The computer can debug USB-TTL. Suitable for portable. Two sets of antenna SMA ports, GPS and GSM antennas are provided.

ESP-WROOM-02 development board D1 For Nodemcu wifi Internet of Things

Thermoelectric Peltier Refrigeration Cooling System Kit Cooler for DIY TEC-12706 mini air conditioner

Semiconductor coolers are a form of solid state cooling that incorporates both semiconductor ​Technologies and electronic assembly techniques. Here is the Kit you can made cooling system for yourself easy and fun Enjoy the DIY

2x6W DC 5V 3.7V speaker modified Stereo Bluetooth amplifier board can connected lithium battery with charge management A8-020

100% Brand New Size: 7x4x0.7cm Conversion:1cm=0.39inch /1 inch =2.54cm

LCD1602 yellow-green screen 1602A lcd display blue

69.5*21.8*17.8 weighs about 30 grams

Wireless Charger 10W 7.5W PCBA Circuit Board Coil Module DIY Charger

The input voltage: 5V2A output : 5V1A The input voltage: 5V4A 9V1.67A(qc3.0) Output : 5V2A 9V1A Charging current: 1000mAh Charging power: up to 10W Wireless conversion efficiency: 73%, boost circuit 90%

TPA3116D2 high power /HIFI digital 2.1 power amplifier board 10-25V

Product Name: high power digital 2.1 power amplifier board Chip type: tpa3116d2 * 2 Input voltage: dc10-25v (DC) Output power: 50wx2 + 100wxi Max Channel: dual channel + 0.1 subwoofer Output impedance: 4-8 Ω Frequency response 20Hz-20KHz Protection function: short circuit overheat power supply anti reverse connection Switching frequency: 1.2MHz Features: power on delay / anti shock Size: about 88 * 66 * 27.6m Net weight: about 105g

Data transmission/transceiver/SI4432 industrial grade Wireless RF receiver cc1101 module

ACS712ELC-05B 5A range ACS712 module AC current sensor module

1. Current sensor chip: ACS712ELC-05B; 2. Pin 5V power supply, onboard power indicator; 3. The module can measure plus or minus 5A current, corresponding to the analog output 185mV/A; 4. When no detection current passes, the output voltage is VCC/2; 5. PCB board size: 31(mm)x13(mm);

DC 12V-24V TPA3118 60W Mono Digital Audio Power Amplifier Board Amp Module

product description: Power amplifier chip: TPA3118 Amplifier power: 1*60W Supply voltage: 8~24VDC Speaker impedance: 4-8Ω Size: 46*35*1.6mm (length, width and thickness) Total height of the board: 12mm

MH-Z19B CO2 detection sensor module Infrared carbon dioxide sensor

MH-Z19B 0-5000PPM Mh-z19c 400-5000ppm C is an upgrade of B Carbon dioxide gold shell (non mh-z19) 400-5000ppm Carbon dioxide white shell (non mh-z19) 400-5000ppm

BLE 4.0 serial port patch type cc2540 cc2541 data transparent transmission iBeacon module

☆Ultra-low standby power consumption 90uA~400uA ☆ Ultra-long connection distance 100 feet/60 meters ☆Super fast response speed 0.4 seconds ☆ Android, Apple, PC, MAC are all universal. ☆No byte limit for sending and receiving, up to 3K Bytes/sec ☆ No need to do MFI ☆ IOS system is perfectly supported. ☆Android 4.3 system is perfectly supported.
Previous： USB Power Bank Charger Circuit Board Step Up Boost Power Module + 5S 18650 Li-ion Case Shell DIY Kit Powerbank
Next： New version ESP-12E (replace ESP-12) ESP8266 remote serial Port WIFI wireless module ESP8266-12E ESP12E
Return
TOP
86-755-83877216
smartbes
smartbes