Search

New version ESP-12E (replace ESP-12) ESP8266 remote serial Port WIFI wireless module ESP8266-12E ESP12E

Products > WIFI/GPS/GMS Module > New version ESP-12E (replace ESP-12) ESP8266 remote serial Port WIFI wireless module ESP8266-12E ESP12E
    • 1
    • 2

New version ESP-12E (replace ESP-12) ESP8266 remote serial Port WIFI wireless module ESP8266-12E ESP12E

ESP8266-12E Is an enhanced version ESP8266-12 , improve the external circuit, enhanced impedance signal output is better, whether it is stable or anti-jamming capability , have been greatly improved ! Before selecting a user for ESP-12 's , it does not matter even if the product has been made , enhanced version is fully compatible with previous firmware pin has added the ESP-12 on the basis of six IO ports , SPI mouth leads , develop more convenient, application more extensive !
shared：


ESP8266-12E  Is an enhanced version ESP8266-12 , improve the external circuit, enhanced impedance
signal output is better, whether it is stable or anti-jamming capability , have been greatly improved !
Before selecting a user for ESP-12 's , it does not matter even if the product has been made , enhanced version
is fully compatible with previous firmware pin has added the ESP-12 on the basis of six IO ports , SPI mouth leads ,
develop more convenient, application more extensive !
 

Description:

Model:ESP8266-12
ISM 2.4GHz
PA +25dBm
802.11b/g/n

 
Warnings:
 
1.This module requires a 3.3 volt supply for VCC, and 3.3V logic.
2.It is not 5V tolant,Connect RX or TX on 5V for ardu will destroy this module.
3.You must use a logic level converter, or a 3.3V for ardu

4.The 3.3V supply on the for ardu has inadequate current capabilit to power this module.

5.You must provide a separate,higher 3.3V supply(about 300mA or better) 
 
 New version ESP-12E (replace ESP-12) ESP8266 remote serial Port WIFI wireless module ESP8266-12E ESP12E





Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit

MH-Z19B CO2 detection sensor module Infrared carbon dioxide sensor

MH-Z19B 0-5000PPM Mh-z19c 400-5000ppm C is an upgrade of B Carbon dioxide gold shell (non mh-z19) 400-5000ppm Carbon dioxide white shell (non mh-z19) 400-5000ppm

16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685 DIY Servo Shield Module

Electric Unit PAM8610 12V 2x15W Dual Channel Stereo C Digital power amplifier board

This plate with switching function, SW short, will turn off the power amplifier Working Mode: Class D (PWM modulation type) Chip Type: PAM8610 Power Range: DC 6V-15V (self-protection) Recommended Voltage: DC 12V(2A) Output Power: 10Wx2(8Ω) 15Wx2(4Ω) Frequency Response: 20HZ-15KHZ Static Current: 20MA (DC12V) SNR: 90% Recommended Speakers: 10-100W Input Impedance: 15K Output Impedance: 4-8Ω Harmonic Distortion: <0.1% Size: Approx. 3cm x 2.5cm/ 1.19" x 0.98"

BLE 4.0 serial port patch type cc2540 cc2541 data transparent transmission iBeacon module

☆Ultra-low standby power consumption 90uA~400uA ☆ Ultra-long connection distance 100 feet/60 meters ☆Super fast response speed 0.4 seconds ☆ Android, Apple, PC, MAC are all universal. ☆No byte limit for sending and receiving, up to 3K Bytes/sec ☆ No need to do MFI ☆ IOS system is perfectly supported. ☆Android 4.3 system is perfectly supported.

HC-SR501 Adjust IR Pyroelectric Infrared PIR Motion Sensor Detector Module

Automatic induction: When someone enters its induction range, enter the high level, people leave the sensor range is automatically delayed off high. Output low. 2. photosensitive control (optional): the module reserved for location, can be set to photosensitive control, strong light during the day or not induction. Photosensitive control is optional, the factory did not install photosensitive resistor. If necessary, please buy a separate photosensitive resistor to install.

Power Supply for Raspberry Pi 3, Raspberry Pi Pro V1.1 UPS HAT I2C Lithium Battery Expansion Board

This is a power expansion Board especially designed for Raspberry Pi, which enables to use the Raspberry Pi with a moveable power source. It's more convenient to use external 3.7V Lithium battery or 3.7V 18650 Lithium battery;

MP3 decoder board, lossless car speaker audio amplifier board modified diy audio receiver module 4.1

Feature Power Supply： 3.7-5V SNR：90dB THD+N：-70dB Crosstalk：-86dB DNR：91dB Support Profile：A2DP/AVCTP/AVDTP/AVRCP/HFP LOS：>15m

High Power TDA3116D2 Two Channel Audio Digital Amplifier Board 12-24V 100Wx2

Item: XH-M190 Name: Digital Audio Amplifier Model: XH-M190 The number of chips: dual-core chips Chip Name: TPA3116D2 Input power: DC12V-24V Output power: 100Wx2 Input Impedance: 51Kx2 Power efficiency:> 90% Output resistance: 4-8Ohm Frequency range: 14-100KHz Noise ratio: 100db Output channel: left and right dual channel Size: 105 * 65 * 23MM Net weight: 90g

Long Range Rfid 134.2 KHZ Reader module RDM660 Writer Transceivers

Wedding special igniter 12V DC universal high voltage generator pulse high voltage module output 60KV arc

1.2V 12V ZB2L3 18650 Li-ion Lithium Battery Capacity Resistance Lead-acid Meter Discharge Tester

Maximum support 15V 3A discharged through the discharge voltage and current, itself does not discharge Maximum capacity statistics support 9999Ah (9999000mAh) Automatically identify and develop appropriate battery termination voltage can also be manually adjusted

DC 12V-24V TPA3118 60W Mono Digital Audio Power Amplifier Board Amp Module

product description: Power amplifier chip: TPA3118 Amplifier power: 1*60W Supply voltage: 8~24VDC Speaker impedance: 4-8Ω Size: 46*35*1.6mm (length, width and thickness) Total height of the board: 12mm

HD SPI 0.96 inch 1.3 inch 1.44 inch 1.8" tft spi st7735 80 x 160 color display OLED LCD screen st7735
Previous： MT3608 2A Max DC-DC Step Up Power Module Booster Power Module
Next： 5A DC to DC CC CV Lithium Battery Step down Charging Board Led Power Converter module XL4015
Return
TOP
86-755-83877216
smartbes
smartbes