Search

Nano V3.0 CH340 improved version Atmega328P USB to TTL with USB cable

Products > Other Module > Nano V3.0 CH340 improved version Atmega328P USB to TTL with USB cable
    • 1
    • 2
    • 3

Nano V3.0 CH340 improved version Atmega328P USB to TTL with USB cable

Technical parameters :
1.12 digital input / output port D2 to D13
2.8 analog inputs A0 ~ A7
3.1 pairs TTL level serial transceiver port RX / TX
4.6 PWM port , D3 , D5, D6, D9 , D10 , D11
5. Atmel ATmega328P - AU MCU
6 USB download and power
7. Support the external 5V ... 12V DC power supply
8. To support 9V battery powered
9. support ISP download
shared：



Nano V3.0 CH340 improved version Atmega328P USB to TTL with USB cable 

Technical parameters :
1.12 digital input / output port D2 to D13
2.8 analog inputs A0 ~ A7
3.1 pairs TTL level serial transceiver port RX / TX
4.6 PWM port , D3 , D5, D6, D9 , D10 , D11
5. Atmel ATmega328P - AU MCU
6 USB download and power
7. Support the external 5V ... 12V DC power supply
8. To support 9V battery powered
9. support ISP download

Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit

W1209 LED Digital Thermostat Temperature Control Thermometer Thermo Controller Switch Module DC 12V Waterproof NTC Sensor

Temperature range :-50-110 ° Dimensions: 48.5 * 40mm Temperature control mode: ON / OFF Resolution:When temperature is 0.1°, the resolution is -9.9~99.9, other temperature segment is 1° Control accuracy: 0.1 ° Hysteresis accuracy: 0.1° Refresh rate: 0.5S High temperature protection: 0-110° Supply voltage: DC 12V Static current: ≤ 35MA, attract current ≤ 65MA Output voltage: DC 12V Output power: 20A relay

PIR IR Light Motion Sensor Infrared Human Induction Lamp Switch 220V 50HZ Lights Control Ceiling On Off 3-6m Sensing

Product Parameter: 1.Sensing Mode:PIR sensing + light control 2.Rated Voltage:220V 50HZ 3.Output Way:Controllable Silicon 4.Load Power:filament lamp ≤100W electricity saving lamp ≤30W LED≤18W 5.Delay:20s (people are moving within the sensing range, the switch will auto delay ​and keep connecting;if people stay still,switch will stop responsing) 6.Sensing Distance:3-6m (high temperature will influence switch sensibility) 7.Sensing Angle:110° 8.Sensitivity to light :darkeness

0.96 Inch LED Display Module OLED With 12864 ICC Interface Module

DC DC Boost Converter Constant Module Current Mobile Power Supply 250W 10A LED Driver Module Non-isolated Step Up Module

Applications: 1, DIY a power supply, 12V can input and output can 12-50V adjustable. 2, the power supply for your electronic device, according to your system can set the output voltage value. 3, as the car power supply for your laptop, PDA or a variety of digital products supply. 4, DIY a mobile notebook power supply: 12V coupled with high-capacity lithium battery pack, so you can go where light where books. 5, solar panel regulator.

Power Supply for Raspberry Pi 3, Raspberry Pi Pro V1.1 UPS HAT I2C Lithium Battery Expansion Board

This is a power expansion Board especially designed for Raspberry Pi, which enables to use the Raspberry Pi with a moveable power source. It's more convenient to use external 3.7V Lithium battery or 3.7V 18650 Lithium battery;

4S 40A Li-ion Lithium Battery 18650 Charger PCB BMS Protection Board For 14.8V 16.8V Lipo Cell Module

4 string 16.8V 40A lithium battery protection board (comes with recovery function-AUTO Recovery) Scope: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650,26650, polymer lithium battery) Product Size: 45 * 55 * 3.4mm (Standard Edition / Enhanced), 46 * 60 * 3.4mm (balanced version) Product weight: 9.3g (standard / enhanced version), 10.3g (balanced version) Charging voltage: 16.8V - 18.1V

GSM module, SIM808 Module with GPS antenna GSM GPRS GPS development board

This module is 5-12V power supply, when the power supply is less than 9V, 2A DC is required. The other power supply port is 3.5-4.2V, suitable for lithium battery power supply. The computer can debug USB-TTL. Suitable for portable. Two sets of antenna SMA ports, GPS and GSM antennas are provided.

43A current limiting control semiconductor refrigeration driven high-power intelligent vehicle motor drive module BTS7960

MH-Z19B CO2 detection sensor module Infrared carbon dioxide sensor

MH-Z19B 0-5000PPM Mh-z19c 400-5000ppm C is an upgrade of B Carbon dioxide gold shell (non mh-z19) 400-5000ppm Carbon dioxide white shell (non mh-z19) 400-5000ppm

XL4016 DC/CC Adjustable 0.2- 9A 300w Step Down Buck Converter 5-40V To 1.2-35V Power Supply Module LED Driver

Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Detailed Images

3.5" inch 480*320 MCU SPI Serial TFT LCD Module Display Screen with Touch Panel Build-in Driver ILI9486

100% brand new and high quality Features: Vivid TFT Display in 65K Color. Touch Panel Selected. SPI Interface, 4 IOs only. With SD Card Extended (Except 1.44"). Module Display Screen only, other accessories demo in the picture is not included.

TTGO T-Display ESP32 WiFi And Ble Module Development Board

Chipset： ESPRESSIF-ESP32 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessor FLASH： QSPI flash 4MB SRAM： 520 kB SRAM Button： Reset USB to TTL： CP2104 Modular interface： UART,SPI,SDIO,I2C,LED PWM,TV PWM,I2S,IRGPIO,ADC,capacitor touch sensor,DACLNA pre-amplifier

4S 30A High Current Li-ion Lithium Battery 18650 Charger Protection Board 14.4V 14.8V 16.8V BMS

1. Module name: 4 series lithium battery protection board 2. Modular nature: polymer lithium battery protection board 3. Overcharge detection voltage: 4.25 ± 0.025V 4. Overcharge release voltage: 4.15 ± 0.05V 5. Overdischarge detection voltage: 2.50 ± 0.08V 6. Over-discharge termination voltage: 3 ± 0.1V 7. Overcurrent: 20-30A

TDA7293/TDA7294 Mono Channel Amplifier Module Circuit PCB Bare Board 4XFB

Model: TDA7293/TDA7294 Power supply: double AC 15V to 36V (AC needs rectification and filtering) or DC positive and negative 18V to 50V.Recommended double 35V (Note that it is not a dual 35V transformer, it is positive and negative 35V DC. And It is recommended to double 26V/200W toroidal transformer, after rectification voltage is about DC double 35V).
Previous： BMS 4S 14.8V 16.8V 18650 lithium battery protection board 40A current
Next： MLX90640BAA/B 32 * 24 infrared temperature measurement dot matrix sensor module Infrared imaging/IR thermal imager camera module
Return
TOP
86-755-83877216
smartbes
smartbes