Search

3.5-inch TFT LCD display screen module serial port SPI driver ILI9488 with capacitive touch RGB320 * 480

Products > Modules > 3.5-inch TFT LCD display screen module serial port SPI driver ILI9488 with capacitive touch RGB320 * 480
    • 1
    • 2
    • 3
    • 4
    • 5

3.5-inch TFT LCD display screen module serial port SPI driver ILI9488 with capacitive touch RGB320 * 480

shared：
3.5-inch TFT LCD display screen module serial port SPI driver ILI9488 with capacitive touch RGB320 * 480
Product Name
3.5 inch lcd 480*320
Type
TFT
Driver chip
Screen ILI9488 Touch FT6236
Module interface
4-wire SPI interface
Effective display area (AA area)
48.96x73.44 (mm)
Module PCB base plate size
55.1x96.18 (mm)
Power consumption
approximately 90mA
VCC power supply voltage
3.3V~5V
Logic IO port voltage
3.3v (TTL)
Product weight
30 (g)
Product Introduction:3.5-inch color screen, supporting 65K color display, with rich display colors 480X320 high-definition resolution with capacitive touch function Using SPI serial bus, only a few IOs are needed to light up the display Equipped with SD card slot for easy expansion of experiments Provide rich sample programs Military grade process standards, long-term stable work Provide technical support for underlying drivers
Serial Number
Label
Pin Description
1
VCC
power input (3.3V~5V)
2
GND
power supply ground
3
CS
LCD film selection
4
RESET
LCD reset
5
DC
LCD bus command/data selection
6
SDI (MOSI)
LCD SPI display bus data input
7
SCK
LCD SPI display bus clock signal
8
LED
LCD backlight control (high level illumination)
9
SDO (MISO)
LCD SPI display bus data input and output
10
NC/3V3

11
CTP-SDA
capacitive touch data output
12
CTP-SCL
capacitive touch clock signal
13
CTP-INT
capacitive touch interrupt signal
14
CTP-RST
capacitive touch chip selection signal
Purchase Notes

This product link contains Two SKU. The price of each SKU is different. Please specify which SKU you need,

and then ask the salesman for a quotation. （Page price for reference only）

3.5-inch capacitive touch LCD module

IPS-3.5 inch capacitive touch LCD module


Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit

PIR IR Light Motion Sensor Infrared Human Induction Lamp Switch 220V 50HZ Lights Control Ceiling On Off 3-6m Sensing

Product Parameter: 1.Sensing Mode:PIR sensing + light control 2.Rated Voltage:220V 50HZ 3.Output Way:Controllable Silicon 4.Load Power:filament lamp ≤100W electricity saving lamp ≤30W LED≤18W 5.Delay:20s (people are moving within the sensing range, the switch will auto delay ​and keep connecting;if people stay still,switch will stop responsing) 6.Sensing Distance:3-6m (high temperature will influence switch sensibility) 7.Sensing Angle:110° 8.Sensitivity to light :darkeness

TPA3118 Mono Digital Amplifier Module Board High Sound Quality 60W

TTP223 touch button module self-locking inching capacitor switch single circuit reconstruction

TTP223 touch button module self-locking inching capacitor switch single circuit reconstruction (D2A4) Size:15mmX11MM Supply:2.5v-5.5v

High Power TDA3116D2 Two Channel Audio Digital Amplifier Board 12-24V 100Wx2

Item: XH-M190 Name: Digital Audio Amplifier Model: XH-M190 The number of chips: dual-core chips Chip Name: TPA3116D2 Input power: DC12V-24V Output power: 100Wx2 Input Impedance: 51Kx2 Power efficiency:> 90% Output resistance: 4-8Ohm Frequency range: 14-100KHz Noise ratio: 100db Output channel: left and right dual channel Size: 105 * 65 * 23MM Net weight: 90g

Power Supply for Raspberry Pi 3, Raspberry Pi Pro V1.1 UPS HAT I2C Lithium Battery Expansion Board

This is a power expansion Board especially designed for Raspberry Pi, which enables to use the Raspberry Pi with a moveable power source. It's more convenient to use external 3.7V Lithium battery or 3.7V 18650 Lithium battery;

4S 30A High Current Li-ion Lithium Battery 18650 Charger Protection Board 14.4V 14.8V 16.8V BMS

1. Module name: 4 series lithium battery protection board 2. Modular nature: polymer lithium battery protection board 3. Overcharge detection voltage: 4.25 ± 0.025V 4. Overcharge release voltage: 4.15 ± 0.05V 5. Overdischarge detection voltage: 2.50 ± 0.08V 6. Over-discharge termination voltage: 3 ± 0.1V 7. Overcurrent: 20-30A

XL4016 DC/CC Adjustable 0.2- 9A 300w Step Down Buck Converter 5-40V To 1.2-35V Power Supply Module LED Driver

Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system.

Original UNO R3 development board original single-chip C language programming learning motherboard kit

Long Range Rfid 134.2 KHZ Reader module RDM660 Writer Transceivers

DC5V-12V Charging module for lithium battery 18650 UPS voltage converter uninterruptible power supply module

Product parameters: Starting voltage: 1.2V Working voltage: 2V-6.5V Output voltage: 5V/9V/12V optional Working voltage is 2V-6.5V Input current: 2A Output power: ≤8W (no matter how high it is, it is easy to overheat) No-load current 2-3.5mA (input 1.5V output 12V) Board size: 33*16*6.5mm Output pad: USB/DC optional

5A DC to DC CC CV Lithium Battery Step down Charging Board Led Power Converter module XL4015

Three in one: (1) Use as an ordinary step-down module with over-current protection capability; (2) Used as a charger for various voltage values of lithium batteries, batteries, nickel-cadmium nickel-metal hydride batteries (battery pack), used in solar panels, wind turbines and other occasions; (3) Use as a high-power LED constant current drive module

Dual coil fast wireless charger transmitter module PCBA board + 2 coil general qi standard diy board

Product Parameters 1. Input power supply: 5V 2A or 9V 1.67-2a, output: 5V 1A or 9V 1.2A 2. Product weight: 0.035kg 3. Charging power: 5W / 7.5w/10w automatic identification 4. Transmission distance: 2-8mm 5. Executive standard: Qi wireless charging standard 6. Product certification: CE / FCC / RoHS

DC 12V-24V TPA3118 60W Mono Digital Audio Power Amplifier Board Amp Module

product description: Power amplifier chip: TPA3118 Amplifier power: 1*60W Supply voltage: 8~24VDC Speaker impedance: 4-8Ω Size: 46*35*1.6mm (length, width and thickness) Total height of the board: 12mm

XL 6009 DC to DC Step Up Converter xl6009 step-up power module dc motor

This DC-DC Module is based on IC XL6009E1 which is a high-performance step-up switching current (BOOST) module. The module uses the second generation of high-frequency switching technology XL6009E1 core chip that offers superior performance over the first generation technology LM2577. XL6009 replaces LM2577 module as LM2577 is about to be phased out.
Previous： GY-85 BMP085 Sensor Modules 9 Axis Sensor Module ITG3205+ADXL345 + HMC5883L 6DOF 9DOF IMU Sensor
Next： Wemos Mini D1 ESP32 WiFi For Wemos D1 Mini Esp8266 Module With Pins
Return
TOP
86-755-83877216
smartbes
smartbes