Search

Raspberry pi zero camera module OV5647 500W RPI zero v1.3 camera

Products > Raspberry Pi Series > Raspberry pi zero camera module OV5647 500W RPI zero v1.3 camera
    • 1

Raspberry pi zero camera module OV5647 500W RPI zero v1.3 camera

5 million pixels
Light-sensitive chips OV5647
Camera parameters:
The CCD size: 1/4 inch
Viewing Angle (Diagonal) : 72.4 degrees
The best pixel sensor: 1080 p
Static image resolution is 2592 x 1944
Support 1080 p30, 1080 p60 and 720 x480p60/90 video footage
Overall size: 60 mm x 11.5 mm x 5 mm
shared：



5 million pixels
Light-sensitive chips OV5647
Camera parameters:
The CCD size: 1/4 inch
Viewing Angle (Diagonal) : 72.4 degrees
The best pixel sensor: 1080 p
Static image resolution is 2592 x 1944
Support 1080 p30, 1080 p60 and 720 x480p60/90 video footage
Overall size: 60 mm x 11.5 mm x 5 mm



Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit

TTP223 touch button module self-locking inching capacitor switch single circuit reconstruction

TTP223 touch button module self-locking inching capacitor switch single circuit reconstruction (D2A4) Size:15mmX11MM Supply:2.5v-5.5v

RS422 to TTL/UART/MCU Serial Port Signal Mutual Module with Over-Voltage Over-Current Protection-3.3V

VCC: + 3.3V TXD : The module's TTL (UART) to send, connected to the microcontroller's RXD receiver pin; RXD : The module's TTL (UART) receiver, connected to the microcontroller TXD send pin; GND : The module ground wire (this wire must be connected with the ground wire of microcontroller system);

DC DC Boost Converter Constant Module Current Mobile Power Supply 250W 10A LED Driver Module Non-isolated Step Up Module

Applications: 1, DIY a power supply, 12V can input and output can 12-50V adjustable. 2, the power supply for your electronic device, according to your system can set the output voltage value. 3, as the car power supply for your laptop, PDA or a variety of digital products supply. 4, DIY a mobile notebook power supply: 12V coupled with high-capacity lithium battery pack, so you can go where light where books. 5, solar panel regulator.

ACS712ELC-05B 5A range ACS712 module AC current sensor module

1. Current sensor chip: ACS712ELC-05B; 2. Pin 5V power supply, onboard power indicator; 3. The module can measure plus or minus 5A current, corresponding to the analog output 185mV/A; 4. When no detection current passes, the output voltage is VCC/2; 5. PCB board size: 31(mm)x13(mm);

DC 12V-24V TPA3118 60W Mono Digital Audio Power Amplifier Board Amp Module

product description: Power amplifier chip: TPA3118 Amplifier power: 1*60W Supply voltage: 8~24VDC Speaker impedance: 4-8Ω Size: 46*35*1.6mm (length, width and thickness) Total height of the board: 12mm

TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection

DC-DC XL7015 module 5V-80V 0.8A Dc converter Step-down module Wide voltage input better than XL7005A

BLE 4.0 serial port patch type cc2540 cc2541 data transparent transmission iBeacon module

☆Ultra-low standby power consumption 90uA~400uA ☆ Ultra-long connection distance 100 feet/60 meters ☆Super fast response speed 0.4 seconds ☆ Android, Apple, PC, MAC are all universal. ☆No byte limit for sending and receiving, up to 3K Bytes/sec ☆ No need to do MFI ☆ IOS system is perfectly supported. ☆Android 4.3 system is perfectly supported.

MH-Z19B CO2 detection sensor module Infrared carbon dioxide sensor

MH-Z19B 0-5000PPM Mh-z19c 400-5000ppm C is an upgrade of B Carbon dioxide gold shell (non mh-z19) 400-5000ppm Carbon dioxide white shell (non mh-z19) 400-5000ppm

LORA RFM95 RFM95W 868 915 RFM95-868MHz RFM95-915MHz SX1276 wireless transceiver module

The RFM95 transceiver is a LoRaTM remote communication module, which provides ultra long distance spread spectrum communication and has super strong anti-interference capability and ultra low current consumption.

Mini Ble Audio Receiver Amplifier Board Module With Stereo Speakers

DC5V-12V Charging module for lithium battery 18650 UPS voltage converter uninterruptible power supply module

Product parameters: Starting voltage: 1.2V Working voltage: 2V-6.5V Output voltage: 5V/9V/12V optional Working voltage is 2V-6.5V Input current: 2A Output power: ≤8W (no matter how high it is, it is easy to overheat) No-load current 2-3.5mA (input 1.5V output 12V) Board size: 33*16*6.5mm Output pad: USB/DC optional

HUB USB expansion board USB HUBS splitter expansion module suitable for Raspberry Pi 4B/3B+/3A+/3B/2B/B+/A+/zero/w

Features: 4 USB expansion ports, compatible with USB2.0 / 1.1 transmission USB to UART for Raspberry Pi for serial debugging Multiple indicators for easy access to power, USB to UART and USB expansion interface Operating voltage: 5V Product Size: 65mm × 30mm Fixed hole diameter: 3.0mm Not include Raspberry Pi

MAX485 Module RS-485 TTL to RS485 MAX485CSA Converter Module

1 on-board MAX485 chip , is a tool for RS-485 communications , low-power , Slew-Rate Transceiver 2 onboard then 5.08 (mm) pitch 2P terminal for easy wiring RS-485 communication 3 the chip has drawn all of the pins can be controlled by the microcontroller operation 4 Working voltage : 5V 5 board size : 44 (mm) x14 (mm)
Previous： 2x6W DC 5V 3.7V speaker modified Stereo Bluetooth amplifier board can connected lithium battery with charge management A8-020
Next： PAM8403 Wireless Stereo Audio Receiver Module For Digital Amplifier Sound Loud Board Micro USB Ble 4.0 3W+3W
Return
TOP
86-755-83877216
smartbes
smartbes