Search

Electric Unit PAM8610 12V 2x15W Dual Channel Stereo C Digital power amplifier board

Products > Amplifier Board > Electric Unit PAM8610 12V 2x15W Dual Channel Stereo C Digital power amplifier board
    • 1
    • 2
    • 3
    • 4
    • 5

Electric Unit PAM8610 12V 2x15W Dual Channel Stereo C Digital power amplifier board

This plate with switching function, SW short, will turn off the power amplifier
Working Mode: Class D (PWM modulation type)
Chip Type: PAM8610
Power Range: DC 6V-15V (self-protection)
Recommended Voltage: DC 12V(2A)
Output Power: 10Wx2(8Ω) 15Wx2(4Ω)
Frequency Response: 20HZ-15KHZ
Static Current: 20MA (DC12V)
SNR: 90% Recommended
Speakers: 10-100W
Input Impedance: 15K
Output Impedance: 4-8Ω
Harmonic Distortion: <0.1%
Size: Approx. 3cm x 2.5cm/ 1.19" x 0.98"
shared：



This plate with switching function, SW short, will turn off the power amplifier
Working Mode: Class D (PWM modulation type)
Chip Type: PAM8610
Power Range: DC 6V-15V (self-protection)
Recommended Voltage: DC 12V(2A)
Output Power: 10Wx2(8Ω) 15Wx2(4Ω)
Frequency Response: 20HZ-15KHZ
Static Current: 20MA (DC12V)
SNR: 90% Recommended
Speakers: 10-100W
Input Impedance: 15K
Output Impedance: 4-8Ω
Harmonic Distortion: <0.1%
Size: Approx. 3cm x 2.5cm/ 1.19" x 0.98"

Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit

Raindrop sensor module/rain sensor/large area raindrop module

* Distribution bit to adjust sensitivity * A fixed bolt hole for easy installation * Power indicator, the output signal LED indicator * The comparator output, the signal is clean, waveform, driving ability over 15mA * Wide voltage LM393 comparator * A large area of rain board, more conducive to detect rain * Board with positioning holes to facilitate installation * Raindrops and control panels are separate, easy to wire leads

Wedding special igniter 12V DC universal high voltage generator pulse high voltage module output 60KV arc

HC-05 master-slave integrated BlE module DIY wireless serial port transparent electronic module BLE

IRS2092S 500W Mono Channel Digital Amplifier Class D HIFI Power Amp Board 20Hz-20KHz Digital Amplifier Module

TPA3110 XH-A232 30W+30W 2.0 Channel Digital Stereo Audio Power Amplifier DC 8-26V 3A C6-001 3110 Amplifier Board

GY-BME/BMP280 3.3V-5V temperature and humidity/atmospheric pressure sensor module

43A current limiting control semiconductor refrigeration driven high-power intelligent vehicle motor drive module BTS7960

TTL Turn RS485 Module 485 to Serial UART Level Mutual Conversion Hardware Automatic Flow Control Module

Product parameters: Operating voltage: compatible with 3.3V and 5.0V Support baud rate: 110-256000bps Operating temperature: -40 Celsius to +85 Celsius Communication signal: compatible with 3.3V and 5.0V

STM32F103C8T6 ARM STM32 Minimum System Development Board Module

CH32F103C8T6 chip is compatible with STM32F103C8T6 series chips, all pins are compatible, all registers are compatible.

TTP223 TTP223B Jog digital touch sensor capacitive touch touch switch modules Accessories

The module is a capacitive touch switch module based on touch detection IC (ttp223b). Under normal condition,the module outputs low level and the mode is low power consumption mode; when touching the corresponding position with fingers, the module outputs high level and the mode switches to fast mode; when there is no touch for 12 seconds, the mode switches to low power consumption mode.

Dual coil fast wireless charger transmitter module PCBA board + 2 coil general qi standard diy board

Product Parameters 1. Input power supply: 5V 2A or 9V 1.67-2a, output: 5V 1A or 9V 1.2A 2. Product weight: 0.035kg 3. Charging power: 5W / 7.5w/10w automatic identification 4. Transmission distance: 2-8mm 5. Executive standard: Qi wireless charging standard 6. Product certification: CE / FCC / RoHS

Power Supply for Raspberry Pi 3, Raspberry Pi Pro V1.1 UPS HAT I2C Lithium Battery Expansion Board

This is a power expansion Board especially designed for Raspberry Pi, which enables to use the Raspberry Pi with a moveable power source. It's more convenient to use external 3.7V Lithium battery or 3.7V 18650 Lithium battery;

0.49 inch 0.5 inch OLED 64x32 ssd1315 0.49 OLED display screen highlighted OLED

BH1750FVI digital Light Intensity BH1750 Light Module Light Ball DC5V

Keyes BH1750FVI Digital Light Sensor Module is a kind of integrated circuit of digital light intensity sensor for two-wire serial bus interface. Using the light intensity data collected by the module, the brightness of the LCD and keyboard background lamps can be adjusted. Module resolution can detect wide range of light intensity changes.

HW-658 GSM/GPRS Mould USB GPS Module For Raspberry Pi

Suitable For Raspberry Pi A B A+ B+ Zero 2 3. Connect via 1*8 2.54 separation distance pin header or USB micro data cable. Adopting L80-39 mould project, with 15 x 15 x 4mm Patch aerial. Super low power consumption, quick location. Support Short-circuit Protection and Aerial Detection. Support self-auxiliary AGPS (EASY technology), no need of external memory. Support LOCUS, DGPS, SBAS(WAAS/EGNOS/MSAS/GAGAN).
Previous： For Ardu ISP AT90USB1286, Teensy++ 2.0 Compatible USB AVR Development Board
Next： W1209 LED Digital Thermostat Temperature Control Thermometer Thermo Controller Switch Module DC 12V Waterproof NTC Sensor
Return
TOP
86-755-83877216
smartbes
smartbes